- What does too much compression sound like?
- Should you compress vocals?
- Should vocals be louder than the beat?
- What is a good reverb setting for vocals?
- Should Kick be louder than snare?
- How much should you compress rap vocals?
- What is a fast attack on compression?
- How do you make your voice stand out?
- What is a good compression ratio for vocals?
- Do rappers double their vocals?
- How loud should vocals be in a mix?
- What is the best compressor for vocals?
- Should I master my beat before vocals?
- How loud should my beat be?
- How many compressors do you need for vocals?
- How can I make my voice sound thicker?
What does too much compression sound like?
When you compress too hard with fast attack times, the dynamic range of your mix is squashed.
You’ll end up with something that sounds like this: A song with no room to breathe; as flat as a pancake..
Should you compress vocals?
When used correctly, compression is a key ingredient for vocals that sound professional, modern and radio-ready. When used incorrectly, compression can quickly ruin a good vocal recording and make your music sound amateur and over-processed.
Should vocals be louder than the beat?
Every vocal is different and every song is different as well. But generally speaking, lead vocal should be moderately loud or the loudest element next to your drums in your mix.
What is a good reverb setting for vocals?
Move the pre-delay to about 30-40% or so as a starting point and see how it sounds. With your EQ, maybe set the high-pass around 200Hz and the low-pass at about 12kHz. In a situation like this, you may want to have more body in the reverb. The following example shows a dual-reverb setup.
Should Kick be louder than snare?
The snare is the foundation of the backbeat, and typically one of the loudest elements in the mix. Next, bring the kick fader up until it sounds almost as loud as the snare. It should be loud enough that the low frequencies are rich and powerful, but not so loud that it masks the bottom-end of the snare drum.
How much should you compress rap vocals?
If your rapping to a trap beat which typically is bass heavy than you’re going to need a lot of compression for your vocals to cut through the mix. I would suggest using a ratio of 6:1 or 7:1 depending on the vocal performance and vocal tone. You will want a release of about 160 ms and threshold of -15 to – 20.
What is a fast attack on compression?
Fast Attack & Release Using a fast attack causes the compressor to respond quickly to the initial sound (drum transient), and reduces the gain quickly. Setting a fast release time causes the compressor to reset quickly so the tail of the drum hit won’t be as compressed.
How do you make your voice stand out?
Tip #1 – Here’s a top notch trick to get your vocals to sit on top of the mix nicely. Send everything but the vocals to their own aux, and apply a very subtle compressor (only a few dB’s reduction). Side chain the lead vocals to this compressor. This will dip the track by a 2 or 3 dB’s every time the vocals come in.
What is a good compression ratio for vocals?
4:1A good starting point for a rock vocal would be a 4:1 ratio with a medium-fast attack and a medium release. Then, set the threshold for around 4 to 6dB of gain reduction. Increase or decrease the attack time until you get the right level of forwardness for the mix.
Do rappers double their vocals?
Some times an artist can double the vocals, but the engineer mixes it to where it sounds like 1 vocal. So theres no way to really know exactly how many tracks an artist uses unless your there.
How loud should vocals be in a mix?
If you mix them too loudly, they will stick out. What dB should vocals be recorded at? You should record vocals at an average of -18dB for 24-bit resolution. The loudest parts of the recording should peak at -10dB and be lowest at -24dB.
What is the best compressor for vocals?
Top Vocal Compressor OptionsUREI/Universal Audio 1176: One of the most famous and widely used FET limiting amplifiers of all time. … Teletronix LA-2A: For a cool tube-y sound, you can’t go wrong with an LA-2A. … Empirical Labs Distressor: Another fantastic compressor.More items…•Mar 16, 2019
Should I master my beat before vocals?
Definitely record your vocals to the beat first, then master everything together. … Sometimes those producers will apply a little mastering to their tracks just to pump them up and make them sound loud and impressive.
How loud should my beat be?
So, about how loud should a beat be to sell? … Now, for the customer, when an artist records on a beat, its very hard to do that when the beat is maxed out to 0db. Always give your artists headroom for their mixing, so for me i usually keep my client copies at around -5 / -6 dB to allow enough headroom.
How many compressors do you need for vocals?
Simply put, don’t be afraid to use more than one compressor on a vocal. For beginners who are likely hyperaware of overusing compression, this may seem counterintuitive, but the idea is this: Instead of getting 10+ dB of gain reduction from one processor, use multiple compressors with 2 to 3 dB of gain reduction each.
How can I make my voice sound thicker?
Once you apply these ten techniques, your mixes as a whole will improve.Top-End Boost. … Use a De’Esser. … Remove Resonances. … Control the Dynamics with Automation. … Catch the Peaks with a Limiter. … Use Multiband Compression. … Enhance the Highs with Saturation. … Use Delays Instead of Reverb.More items…•Jan 5, 2017