- What compression is best for 93 octane?
- How is compression ratio calculated?
- What is compressor attack?
- How do I reduce engine compression?
- What comes first EQ or compression?
- Will 93 octane increase HP?
- What is considered a high compression ratio?
- What octane is needed for 11 1 compression?
- What is threshold setting?
- Do high compression engines wear out faster?
- What is the highest compression ratio for 93 octane?
- How do you adjust the threshold on a compressor?
- What happens if engine compression is too high?
- Does high compression make more power?
- What is considered good compression?
- Is 120 psi enough compression?
- What is the compression ratio for 93 octane?
- Should I put a compressor on every track?
- Do I really need a compressor pedal?
- When should you use a compressor?
What compression is best for 93 octane?
If the cylinders are sealing up well, I look for 190 psi as a lower limit with preferably 200 psi as a target when using 93-octane fuel.
For every octane number less than 93, the compression pressure needs to be about 5 psi less to avoid detonation under normal circumstances..
How is compression ratio calculated?
Compression ratio formula It can be calculated according to the cylinder volume formula: Vd = b2 * s * π / 4 . Vc is the volume above the piston when the piston is at the top dead-centre (its topmost position), also called the compressed volume. b is the cylinder bore (diameter). s is the piston stroke length.
What is compressor attack?
The Attack setting controls how long the compressor takes to compress the signal, while the release setting controls how long the compressor takes to let go. … With the right settings, you can use a compressor to smooth out dynamic performances, add attack to transients, or even fatten tracks up with distortion.
How do I reduce engine compression?
Shorter rods & reducing the stroke. A shorter stroke will have a dramatic effect on the compression ratio. By combining this method with low compression pistons one can start to think about running very high boost pressures when adding a turbo.
What comes first EQ or compression?
Each position, EQ pre (before) or EQ post (after) compression produces a distinctly different sound, a different tonal quality, and coloration. As a rule, using EQ in front of your compressor produces a warmer, rounder tone, while using EQ after your compressor produces a cleaner, clearer sound.
Will 93 octane increase HP?
Premium gas must be, by law, at or above 91 percent, although you do also see 93 percent octane ultra-premium at many stations. … Octane does not offer any better fuel mileage, increase engine horsepower, or make the engine start quicker. Higher octane only reduces the likelihood of engine knock or ping.
What is considered a high compression ratio?
Compression ratios usually range from 8:1 to 10:1. A higher compression ratio — say, from 12:1 to 14:1 — means higher combustion efficiency. Higher compression ratios and combustion efficiency mean more power with less fuel, and fewer exhaust gases.
What octane is needed for 11 1 compression?
with the right fuel and ignition curves, and the right cam timing, as well as the best exhaust efficiency, 11:1 on the street is doable. by the way i would tune to run 89 octane, that way if 91 goes away, you can still find gas to run.
What is threshold setting?
A threshold setting is a percentage that controls the total number of data values that are required to meet the threshold before an inference is made by the system. … You can then change the inference in the frequency distribution if you choose.
Do high compression engines wear out faster?
Higher compression engines tend to blow head gaskets a little quicker. As long as the engine is built to handle the high compression there is no issue. Diesels last so long because they are overbuilt like crazy.
What is the highest compression ratio for 93 octane?
12.8:111.5:1 WILL run fine. 12:1 is pushing it, but it’ll run, you may have issues though. Tony Shephard has a 397 stroker with nitrous running 9’s and when he’s off the bottle he’s running 93 octane with 12.8:1 compression. It’s all about the tune honestly.
How do you adjust the threshold on a compressor?
Try starting with a moderate to medium ratio of between 2:1 and 5:1. Set your attack time to a medium-fast setting and your release time to a medium setting. Now, gradually raise the threshold until you’re getting somewhere around 5 dB of gain reduction. Then set your output gain to compensate for the 5 dB attenuation.
What happens if engine compression is too high?
If the compression is too high for the fuel used pre ignition will occur, the mixture will ignite from the heat of being compressed before the piston reaches (at least close to) top dead center.
Does high compression make more power?
This occurs because internal combustion engines are heat engines, and higher compression ratios permit the same combustion temperature to be reached with less fuel, while giving a longer expansion cycle, creating more mechanical power output and lowering the exhaust temperature.
What is considered good compression?
100 psi per cylinderA compression test reveals the condition of your engine’s valves, its valve seats, and piston rings and whether these parts are wearing evenly. Healthy engines should have compression over 100 psi per cylinder, with no more than 10 percent variation between the highest and lowest readings.
Is 120 psi enough compression?
You should start to worry if one of your cylinders is getting close to 100 psi. Most new engines in good condition compress at around 175 psi. … Suppose that #4 cylinder were at 120 psi, the difference ratio would be 31.4% which would indicate excessive wear in the cylinder.
What is the compression ratio for 93 octane?
9.5:1We are being told by most piston manufacturers that 9.5:1 is the most you should run in an engine with cast iron heads on 93 octane pump gas. Because aluminum conducts (dissipates to the cooling system) heat much faster than cast iron does, you can run 10.5:1 with aluminum heads on 93 octane.
Should I put a compressor on every track?
Each compressor on your track should only be reducing the gain by 1-3 dB’s. So instead of using 1 compressor on the bass to turn it down 9dB, try using 3 compressors that are reducing 3 dB each. Though it’s technically the same amount of reduction, your bass is going to sound more dynamic and less compressed.
Do I really need a compressor pedal?
Why Would I Want a Compression Pedal? … When playing staccato chords, a compressor is ideal for getting that classic “squishy” funk guitar tone. For rock or blues leads, a compressor lets you get more sustain, without resorting to using so much distortion that you lose articulation.
When should you use a compressor?
When to Use Compression in Your Mix (3 Situations)When Transients Are Sticking Out of Your Mix. The most basic use for a compressor involves taming transient material using downwards compression. … When Your Mix Isn’t Transient Enough. In addition to attenuating transients, compression allows you to emphasize transients. … When You Want to Create Space.May 30, 2019