- Should you put reverb on everything?
- What makes a great mix?
- How do I make my mix sounds clearer?
- How do you balance instruments in a mix?
- What instruments should be panned?
- Where should the snare sit in the mix?
- How do you mix two instruments?
- Should vocals be panned?
- What dB should kick be at?
- What dB level should I mix at?
- What instrument is the loudest?
- Should snare be panned?
- Where do you put the instruments in the mix?
- How loud should instruments be in a mix?
- How loud should hi hats be in a mix?
- Why is mastering so hard?
- What frequency should a snare be at?
- Where can I pan string?
Should you put reverb on everything?
You can apply any and every effect to a bus just like any other track on your mixer.
Nothing is more important to a song than the instruments themselves.
This means the reverb should never get in the way of anything..
What makes a great mix?
Good mix ( to me [engineer/listener] ) is when you start the track and everything is in a complete frequency balance, harmonically working with each other and complementing every part of the song to the point you understand all the feelings and thoughts in the music you are hearing the artist is trying to portrait to …
How do I make my mix sounds clearer?
10 Mixing tips and tricks to create a clear mixBass your worse enemy.Use Reverb as delay.Side chain compress the import parts that need it.Parallel compress your drums.avoid the stereo imager in the mix use mid side routing instead.phase / delay to create space.notch filter to create space.Subtractive EQ every sound somewhere.More items…•Oct 12, 2016
How do you balance instruments in a mix?
Follow the Leader:Start your mix with the main instrument. This may be the vocal in a pop track or your kick and bass in a club track. … Set your mix to mono. Switch off one monitor. … Generate pink noise at a suitable level. This level should be around where you want your main element to sit in the mix.
What instruments should be panned?
Suggested Panning PositionsInstrumentCommentOverheadsOverheads are best panned fairly wide but should never be too loud as to distract the listenerBass GuitarBass heavy instruments, such as the bass guitar, should be kept near the centre as to not disrupt the balance of the track9 more rows•Apr 26, 2020
Where should the snare sit in the mix?
Low cut up to just below the thump of the snare to clean the mud. You’ll see a bump at the lower end of the snare on the frequency spectrum, this is the body of the snare. In my example below it’s at 200Hz. Listen to the snare in the context of the whole mix and cut or boost it to sit perfectly in your mix.
How do you mix two instruments?
Slice and Dice with EQCut – Cut the same frequency in the snare drum to make the two instruments sit better.Boost – Boost the snare a few frequencies higher to mask the effect of clashing instruments.Reduce – Lower the volume of either instrument to make the clashes sound less severe.
Should vocals be panned?
The best way to give your mix a solid core is to keep lower frequency sounds in the center. That means kicks, basses and anything else below the 120hz range. If your track has lead vocals pan them center as well. … But as a general rule lead vocals should always be panned center.
What dB should kick be at?
Re: Recommended -dB of bass in relation to kick I would recommend you average your levels around -18db or so and after that, while mixing, set your levels in relation to each other rather than the meter per se.
What dB level should I mix at?
I recommend mixing at -23 dB LUFS, or having your peaks be between -18dB and -3dB. This will allow the mastering engineer the opportunity to process your song, without having to resort to turning it down.
What instrument is the loudest?
Boardwalk Hall Auditorium OrganAccording to the Guinness Book of World Records, the loudest (and largest) instrument in the world is the Boardwalk Hall Auditorium Organ. This pipe organ was built by the Midmer-Losh Organ Company, and is housed in the Main Auditorium of the Boardwalk Hall in Atlantic City, New Jersey.
Should snare be panned?
When you’re panning your drum sounds, you want to make sure that the most impactful elements remain at the core of your beat. Therefore, I advise you to leave all the kicks (including 808 kick-drum samples) and snare sounds at the centre. In other words, you don’t need to apply any panning to them.
Where do you put the instruments in the mix?
Because of their lack of directionality, and because they contain most of the energy in a typical mix, it’s best to keep these sounds in the middle of your mix. Create a natural space in the stereo spread for each drum piece. Typically, in a rock or pop mix, the drums and bass are the first element most people address.
How loud should instruments be in a mix?
The ideal listening range for most home studios is around 73-76dB SPL. But mixers have no control over how loud people listen to music. Only how loud each element is in the track. That’s why it’s crucial to make sure that your mix is balanced and each instrument is at the proper level relative to the other channels.
How loud should hi hats be in a mix?
20 dbThe thing you want to create is a “nice even sound” as when your song gets mastered the low and top end will become much louder and much more defined than before. If you absolutely must have a volume level for your hi hats, I would suggest -20 db.
Why is mastering so hard?
The Most Difficult process about Mastering is mastering more than one song at a time. … You need to make every song sound like they belong together. You can’t have one louder than the other and they need to sound similar both in dynamic range and frequency response.
What frequency should a snare be at?
900 HzIdeally, it should work closely with the pulse to make the snare sit well in the mix. Most of this sound is typically found around the 900 Hz–2.0 kHz range.
Where can I pan string?
Panning all of the violins to the left takes the listener’s attention off of the main ingredients, such as a center-panned vocalist or solo instrument because they also often reside in the same range. Instead, pan your string bass parts to the middle to center the mix’s lower end.